Though it can seem intimidating, installing your own batting installation can be easy, and take just a few hours if you isolate the need to a few key spaces. Have a drafty attic? Start there. Concerned about a freezing crawl space? Throw on your work jeans and get to work. These insulating spaces will instantly feel warmer and you’ll notice the savings on your next heating bill. Read how to install insulation here.
Most newer cabinets have self-closing hinges that hold the doors shut. Others have magnetic or roller catches. A catch that no longer keeps a door closed is either broken or out of adjustment. Catches are fastened with two screws, so replacing a damaged catch is simple. Adjustment is just as simple, but you might have to readjust the catch a couple of times before you get it right. Loosen the screws, move the catch in or out, and tighten the screws. If the door doesn’t close tightly, try again.
Many an amateur DIY enthusiast has spotted a job that needs doing and gone out to buy the appropriate tools, only to find that they're way out of their league. Book a handyman using the Handy app or website and you can be sure that they'll arrive with everything they’ll need to get the job done. In addition to your run-of-the-mill screwdrivers and hammers, your handyman specialist will read your job description before they arrive to ensure they come prepared for anything that your specific job may require. Don't worry about whether you’ve got the right tools for the job. Book a handyman through Handy and leave it to the professionals.

How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.


Another related issue for avoiding costly repairs (or disasters) is the proper operation of a home, including systems and appliances, in a way that prevents damage or prolongs their usefulness. For example, at higher latitudes, even a clean rain gutter can suddenly build up an ice dam in winter, forcing melt water into unprotected roofing, resulting in leaks or even flooding inside walls or rooms. This can be prevented by installing moisture barrier beneath the roofing tiles. A wary home-owner should be alert to the conditions that can result in larger problems and take remedial action before damage or injury occurs. It may be easier to tack down a bit of worn carpet than repair a large patch damaged by prolonged misuse. Another example is to seek out the source of unusual noises or smells when mechanical, electrical or plumbing systems are operating—sometimes they indicate incipient problems. One should avoid overloading or otherwise misusing systems, and a recurring overload may indicate time for an upgrade.

Any property repair services are only as good as the people and the tools behind them. That’s why we use only the latest repair and maintenance equipment on every job, no matter how small. Part of our job is to ensure your house is up-to-date and looking its best, so we use only the best resources available in order to make that happen. We offer a variety of handyman services throughout the DC area, including all of the following:
How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.
There’s nothing worse than starting a sink or toilet repair only to find that the shutoff valve won’t shut off. Some shutoff valves are easy to replace. For those that aren’t, turn off the main water valve, remove the packing nut, and then unscrew the stem and take it to the hardware store to find a replacement washer. Clean any grit out of the valve body and pop on the new washer. The valve will work like new.

JW were very prompt to reply to our initial quote request in which we described using the master shower caused water to pour down the HVAC return duct and was collecting within the walls and causing water damage on the first floor and in the basement ceiling. We also reached out to see if they could resolve a water issue in a corner of the basement that had become oversaturated during the heavy DC rains this summer causing heavy mold within the insulation and a few rotted studs (in addition to moldy drywall). Josh quickly scheduled a time to come out and take a look at the situation and provided great upfront information regarding what he thought the issue might be (initially believed a ripped rubber liner in the shower), price estimate, and description of the teams they use to work on projects. He estimated 2 workers over 3-4 days for $5,952.00 to $7,936.00 dependent on the severity of the issue and materials required. Once we scheduled the work, Cesar was out on time (a little early every day) from Monday through midday Wednesday. On site Cesar let me know the issue actually seemed to be bad grouting and caulking from the original house flippers. He offered to re-grout the entire shower and re-caulk, then test the shower instead of tearing up the stone tile on the floor. The next day we tested the shower for 10-15 minutes and no leak! Luckily for us the issue was smaller than expected which saved us a lot of hassle and money and I'm glad he opted to try that before blindly tearing up the shower. Beyond the high quality of work in general, a few things stood out in my mind as to how customer-oriented JW is: 1) Cesar constantly checked in if he wanted our opinion on things before moving forward. 2) Within the main leak area, he sprayed anti-fungal solution to prevent residual build up. 3) In the basement leak area, they sprayed base-level drylock to help prevent further issues. 4) We had plans to paint the areas they worked on so we didn't require they to repaint but it was offered to us. When they learned we planned on painting, they primed the area so it was ready for us when we got to painting it. 5) The cleanup crew collected all leftover materials and some extra left by the original flippers. Overall the project came in under budget and under timeline. We were exceptionally pleased with JW and will continue to use them as we need services like theirs.

×