How to DIY it: You should already be emptying the lint trap before every load of laundry. To do a thorough cleaning of the dryer and its vent duct system, unplug the machine (and turn off the gas valve if it has one). Pry off the access panel on the front (try a putty knife covered with duct tape to prevent scratching) and vacuum around the motor and heating element (above). Then carefully disconnect the vent duct tubing from the back of the dryer and use a dryer vent brush (about $10 at home 
centers; look for one that also cleans refrigerator coils) to pull out any 
accumulated lint. Aim to do this at least once a year.
Plumbing vent boots can be all plastic, plastic and metal, or even two-piece metal units. Check plastic bases for cracks and metal bases for broken seams. Then examine the rubber boot surrounding the pipe. That can be rotted away or torn, allowing water to work its way into the house along the pipe. With any of these problems, you should buy a new vent boot to replace the old one. But if the nails at the base are missing or pulled free and the boot is in good shape, replace them with the rubber-washered screws used for metal roofing systems. You’ll find them at any home center with the rest of the screws. You’ll have to work neighboring shingles free on both sides. If you don’t have extra shingles, be careful when you remove shingles so they can be reused. Use a flat bar to separate the sealant between the layers. Then you’ll be able to drive the flat bar under the nail heads to pop out the nails.
It is instinctual for homeowners to contact an HVAC tech when they notice irregularities in their cooling or heating system. These irregularities could be a direct result of a dirty or clogged air filter. We encourage homeowners to check their filters and replace if necessary. It’s also beneficial for homeowners with pets, carpet, or for homes near fields or construction zones to have multiple filters for convenient replacement.
When that happens, all you can do is pay up, as happened with Jason Hark and Kenneth Larivee. In 2016, the couple got hit with a $28,000 assessment to replace the siding on their West Orange, N.J. townhouse in a condo association. This cost came on top of their $610 monthly association fee. After speaking with siding companies, Mr. Hark estimated that if his unit had been a stand-alone property, the project would have cost closer to $7,500. “But we couldn’t fight it,” said Mr. Hark, a director at WCBS-TV.
Even tasks that seem relatively small can add up. Consider the French doors that David Sievers, 53, and his wife, Ulin Sargeant, 47, installed two years ago to replace sliding glass doors on their two-bedroom house in Monrovia, Calif. The doors cost $2,000. But then they paid $1,700 for installation, $500 for a painter to restore the stucco and paint, and $1,600 for an engineering plan required by the city.

Some see a benefit of franchising as "entrepreneurship under the safety net of a tried-and-true business umbrella"[15] but forecast a 1.2 percent decrease in franchise businesses during the 2008-2009 recession.[15] In 2005, according to a survey released by the Washington-based International Franchise Association showed 909,000 franchised establishments in the United States employing some 11 million people.[15] Franchises offer training, advertising and information technology support, lower procurement costs and access to a network of established operators.[15]
Turn2Us Handyman Services was created with the homeowner in mind. Our goal is to help you with all your household projects by providing a full handyman service or simply providing a handyman to help you with your to-do list. No need to call multiple businesses to handle your projects, we can do it all! We are dedicated to providing you with the best handyman service available at the most affordable price without sacrificing quality.

This summer, they decided to paint the frames black, which cost $900. Mr. Sievers, a special-education teacher, and his wife, a doctor, could have done the work themselves, a solution that do-it-yourself enthusiasts would suggest. But the doors face the street, and the couple wanted the end result to look polished. “My dad and my uncle used to always do home repairs and everything used to come out uneven or crooked,” Mr. Sievers said. So he paid a professional.


Dab any type of kitchen cooking oil (olive, canola or sunflower) onto a paper towel. Then lay the paper towel over the residue that refuses to budge. Wait a few minutes while the oil works to dissolve the stubborn glue. Finally, remove the towel and rub away the sticker residue with another clean paper towel. However, you need to be cautious with stains on more absorbent materials.
Almost nothing is quicker, easier or refreshes a room more than a new coat of paint. Even switching up a bright white for a trendy, bright grey can change your whole perspective and give you a starting point for new colors and decoration. Gallons of paint range from $30-$50, and with primer/paint combinations, you will likely only need a gallon or less to finish an average sized room. Add another $10, and you’ll be set with rollers, paint brushes, and painter’s tape. This DIY repair could potentially save you thousands over the cost of a professional painter. Short on time? Click here to learn how to paint a room fast.
Even tasks that seem relatively small can add up. Consider the French doors that David Sievers, 53, and his wife, Ulin Sargeant, 47, installed two years ago to replace sliding glass doors on their two-bedroom house in Monrovia, Calif. The doors cost $2,000. But then they paid $1,700 for installation, $500 for a painter to restore the stucco and paint, and $1,600 for an engineering plan required by the city.
Intimidated by this seemingly daunting project? Don’t be. If you have the will and a whole day (or two) to yourself, you can refinish the hardwood floors in the major areas of your home. You don’t necessarily need to sand, but if the floor is damaged enough to warrant buffing, check out your local hardware store and rent the equipment for anywhere from 4-48 hours. Here’s how to refinish your hardwood floors.
Plumbing vent boots can be all plastic, plastic and metal, or even two-piece metal units. Check plastic bases for cracks and metal bases for broken seams. Then examine the rubber boot surrounding the pipe. That can be rotted away or torn, allowing water to work its way into the house along the pipe. With any of these problems, you should buy a new vent boot to replace the old one. But if the nails at the base are missing or pulled free and the boot is in good shape, replace them with the rubber-washered screws used for metal roofing systems. You’ll find them at any home center with the rest of the screws. You’ll have to work neighboring shingles free on both sides. If you don’t have extra shingles, be careful when you remove shingles so they can be reused. Use a flat bar to separate the sealant between the layers. Then you’ll be able to drive the flat bar under the nail heads to pop out the nails.
José was quick to respond to my request for an estimate to install a new back door. He came over and sized it up, sent me a fair priced quote the next day, and was back with workers soon after I accepted the quote and immediately started working. I'm extremely satisfied with the work that was performed--and the door needed to be framed and set inside the metal frames for the house, which is a little more complex than a regular door installation. I will definitely hire Jose and Jireh Contractor again!
You may qualify if all of the following apply to your household:A child under six resides in your home or spends at least six hours per week in your home on a regular basis You have owned and lived in your home for more than one yearYour home was built before 1978You live in one of these city neighborhoods:Bond Hill, Westend, Over-The-Rhine, Mt. Auburn, CUF, Corryville, Madisonville, Avondale, South Cumminsville, North and South Fairmount, West, East and Lower Price Hill, Walnut Hills, Evanston Northside or Carthage
×