It is not uncommon for power switches and breakers to be accidentally turned off when other appliances are being installed. Homeowners are encouraged to check their circuit breaker to make sure the issue isn’t as simple as needing to turn a switch back on. A circuit breaker is typically located in the garage, although in some homes, the circuit breaker can be found in the basement, hallway or storage room.
If you have a wallpaper seam that’s coming apart, reactivate the paste around the gap with a rag soaked in warm water. Hold the rag over the area for a minute or two, and then carefully open the gap a little larger so you’ll have more room for the sealer. Squeeze seam sealer (white glue works in a pinch) into the gap, and press the paper to the wall with a roller. Clean off the excess sealer with a sponge.

If you have a wallpaper seam that’s coming apart, reactivate the paste around the gap with a rag soaked in warm water. Hold the rag over the area for a minute or two, and then carefully open the gap a little larger so you’ll have more room for the sealer. Squeeze seam sealer (white glue works in a pinch) into the gap, and press the paper to the wall with a roller. Clean off the excess sealer with a sponge.


A handyman is not the best option for a large or complicated project that could take a long time to complete and requires the help of multiple workers. You shouldn't turn to a handyman either if you need an emergency service for plumbing, electrical or appliance work, unless the handyman is licensed in that trade. If an unlicensed person does plumbing or electrical work, you have no guarantee that the work has been done to code, which could affect your homeowners insurance policy or any claim related to the work. Use a contractor or specialist for remodeling work, room additions and projects that require heavy-duty equipment or licensed professionals like electricians.

So a door knob slammed through the wall after one too many times slamming the door. No need to call your handy contractor. You can easily fix a few holes in your drywall by injecting a setting compound (for smaller holes) or by cutting out the damaged sections and replacing them with new drywall (for larger ones). Check out this handy tutorial for more on repairing holes.
Tiny holes in shingles are sneaky because they can cause rot, a leaky roof and other damage for years before you notice the obvious signs of a leak. You might find holes left over from a satellite dish or antenna mounting brackets or just about anything. And exposed, misplaced roofing repair nails should be pulled and the holes patched. Small holes are simple to fix, but the fix isn’t to inject caulk in the hole. You’ll fix this leaky roof problem with flashing.

Quick-setting drywall compound lets you finish small repairs and fill deep holes in minutes instead of waiting days for premixed joint compound to dry. The small boxes are available in most home centers and paint stores are also easier to store and more likely to get used up than large bags or buckets. Click here to learn how to hang drywall like a pro. Click here to buy drywall compound on Amazon now.


If you have shallow scratches or nicks, hide them with a stain-filled touch-up marker. Dab on the stain and wipe off the excess with a rag. But beware: Scratches can absorb lots of stain and turn darker than the surrounding finish. So start with a marker that’s lighter than your cabinet finish and then switch to a darker shade if needed. For deeper scratches, use a filler pencil, which fills and colors the scratch. Or, try using a walnut to remove scratches in wood!
If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
Business Education Entertainment Government President Obama Visit 2009 General Election Health Live Healthy Non-Profit Sports Obituaries Pet Network Homeless Taskforce Weather Amherst Avon Avon Lake Elyria Grafton LaGrange Lorain North Ridgeville Oberlin Sheffield Lake Sheffield Village Vermilion Wellington LorainCounty.com Blog Digital Partners Advertise with Us
Albany Handymen | Asheville Handymen | Atlanta Handymen | Austin Handymen | Baltimore Handymen | Birmingham Handymen | Boston Handymen | Charlotte Handymen | Chicago Handymen| Cincinnati Handymen | Cleveland Handymen | Columbus Plumber | Dallas Handymen | Denver Handymen | Detroit Handymen | El Paso Handymen | Fort Lauderdale Handymen | Fort Worth Handymen | Fresno Handymen | Grand Rapids Handymen | Greensboro Handymen | Harrisburg Handymen | Hartford Handymen | Houston Handymen | Indianapolis Handymen | Jacksonville Handymen | Kansas City Handymen | Las Vegas Handymen | Long Beach Handymen | Los Angeles Handymen | Louisville Handymen | Madison Handymen | Memphis Handymen | Miami Handymen | Milwaukee Handymen | Minneapolis Handymen | Modesto Handymen | Nashville Handymen | New Orleans Handymen | New York Handymen | Norfollk Handymen | Oklahoma City Handymen | Orlando Handymen | Philadelphia Handymen | Phoenix Handymen | Pittsburgh Handymen | Portland Handymen | Providence Handymen | Raleigh Handymen | Richmond Handymen | Sacramento Handymen | Saint Louis Handymen | Saint Paul Handymen | Salt Lake City Handymen | San Antonio Handymen | San Diego Handymen | San Francisco Handymen | San Jose Handymen | Seattle Handymen | Tampa Handymen | Tucson Handymen | Virginia Beach Handymen | Washington DC Handymen | Winston Salem Handymen | Handymen by State
Albany Handymen | Asheville Handymen | Atlanta Handymen | Austin Handymen | Baltimore Handymen | Birmingham Handymen | Boston Handymen | Charlotte Handymen | Chicago Handymen| Cincinnati Handymen | Cleveland Handymen | Columbus Plumber | Dallas Handymen | Denver Handymen | Detroit Handymen | El Paso Handymen | Fort Lauderdale Handymen | Fort Worth Handymen | Fresno Handymen | Grand Rapids Handymen | Greensboro Handymen | Harrisburg Handymen | Hartford Handymen | Houston Handymen | Indianapolis Handymen | Jacksonville Handymen | Kansas City Handymen | Las Vegas Handymen | Long Beach Handymen | Los Angeles Handymen | Louisville Handymen | Madison Handymen | Memphis Handymen | Miami Handymen | Milwaukee Handymen | Minneapolis Handymen | Modesto Handymen | Nashville Handymen | New Orleans Handymen | New York Handymen | Norfollk Handymen | Oklahoma City Handymen | Orlando Handymen | Philadelphia Handymen | Phoenix Handymen | Pittsburgh Handymen | Portland Handymen | Providence Handymen | Raleigh Handymen | Richmond Handymen | Sacramento Handymen | Saint Louis Handymen | Saint Paul Handymen | Salt Lake City Handymen | San Antonio Handymen | San Diego Handymen | San Francisco Handymen | San Jose Handymen | Seattle Handymen | Tampa Handymen | Tucson Handymen | Virginia Beach Handymen | Washington DC Handymen | Winston Salem Handymen | Handymen by State
Sooner or later, every sprayed ceiling is going to get a water stain or a scrape. Spray texture in a can won’t perfectly match every ceiling texture, but it’s usually close, and a lot easier than respraying a whole ceiling. Before spraying, seal the patch with a stain-blocking primer, cover the floor and furniture, and practice your technique on scrap plywood or cardboard. Buy ceiling texture on Amazon now.
Tired of listening to those cabinet doors bang shut? Peel-and-stick door and drawer bumpers are the solution. Get a pack of 20 at a home center for a few dollars. Make sure the back of the door is clean so the bumpers will stick, then place one at the top corner and another at the bottom. Plus: Keep your kitchen (and whole house!) clean with these 100 brilliant cleaning hacks.

When you book handyman service through Handy, you want to know that they are experienced and capable enough to deal with the job at hand. That’s why we ensure every professional on the Handy platform is rated and reviewed by their past customers. The requirements of different home repair jobs are never quite the same, and so we ensure that we connect you with the best handyman professionals that are able to handle your particular job.


Sussex County Habitat for Humanity offers a Home Repair Program that performs repair services to help low-income homeowners impacted by age, disability and family circumstances reclaim their homes with pride and dignity. Volunteer teams work to improve the condition of homes by painting, landscaping, and performing minor repairs at minimal costs to homeowners who would otherwise be unable to complete home repairs on their own.  In addition, SCHFH now offers home repair and renovation services on a larger scale that aim to alleviate critical health, life and safely issues.  Able-bodied homeowners are asked to work alongside the volunteers in a cooperative effort.
Risk: If your house was built 
before 1994 and still has the original plumbing fixtures, you’re using 
30 to 40 percent more water than 
a comparable new home. Because about 70 percent of the water flowing through the showerhead is hot, 
that means higher heating bills too. A basic showerhead can cost just $15 and could pay for itself in reduced water and heating costs after just one month. Calculate your 
savings at epa.gov/watersense/watersense-calculator.
If a screw turns but doesn’t tighten, the screw hole is stripped. Here’s a quick remedy: Remove the screw and hardware. Dip toothpicks in glue, jam as many as you can into the hole and break them off. You don’t have to wait for the glue to dry or drill new screw holes; just go ahead and reinstall the hardware by driving screws right into the toothpicks.

A variety of problems can befall your home’s doors, especially older doors that may start to sag, stick, develop drafts or experience other issues. Fixing or replacing a door is well within the capabilities of most homeowners, especially if you have a partner to help out. From installing new weather stripping to replacing the lock, you can handle it. Watch this video to see how simple it is to replace an interior door yourself.
If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
How to DIY it: A simple cleaning often solves the problem. Start by pulling out the lower dish rack. 
Remove the spray arm and use a thin piece of wire to clean out the holes where water sprays through. Scoop or vacuum out any leftover food 
particles from the filter area, then 
remove the filter screen (above), if possible, and give it a good rinse.

Simple fixes for the four most common refrigerator problems: an ice-maker breakdown, water leaking onto the floor, a cooling failure and too much noise. Chances are, you can solve the problem yourself, save some money and avoid the expense and inconvenience of a service appointment. The following article will walk you through the simplest solutions to the most common fridge malfunctions. Learn how to repair a refrigerator here.

How well do the franchise chains perform? One Wall Street Journal reporting team did an informal assessment by hiring handymen all over the United States and asking them to fix a wide range of problems, from a relatively routine leaky faucet to a sticky door.[12] The reporter concluded that "with few licensing requirements and standards for the industry, prices are all over the board."[12] One quote was ten times as large as another.[12] Further, the reporter concluded "A big corporate name is no guarantee of quality or speedy service."[12] One corporate firm took three weeks to fix a stuck door.[12] Service varied from spotty to good, with complaints about unreturned phone calls, service people standing on dining room chairs, leaving holes between wood planking, but liked getting multiple jobs done instead of just one.[12] Customers liked handymen wearing hospital booties (to avoid tracking dirt in houses).[12] The reporter chronicled one experience with repairing a water-damaged ceiling. A franchise firm fixed it for $1,530; a second (non-franchise local handyman) fixed a similar ceiling for $125.[12] The reporter preferred the second worker, despite the fact that he "doesn't have a fancy van -- or carry proof of insurance".[12] Tips for selecting a good handyman include: ask questions, get written estimates on company stationery, make sure handymen guarantee their work, pay with credit cards or checks because this provides an additional record of each transaction, check references and licenses,[20] review feedback about the contractors from Internet sites. To find a competent worker, one can seek referrals from local sources such as a school or church or office park, to see if a staff handyman does projects on the side, as well as ask friends for referrals; a general contractor might have workers who do projects on the side as well.[20] Further, one can try out a new handyman with easy projects such as cleaning gutters to see how well they perform.[20]
How to DIY it: Clean up any rough edges around the hole, then stick the patch onto the wall over the hole (left). Using the taping knife, spread a layer of joint compound over it and let it dry overnight. Then spread a wider second coat, feathering out the compound on all sides to make the patch blend in. Let it dry, then apply one more coat extending 8 to 12 inches beyond the patch in 
all directions. After the final coat dries, sand the area with a sanding sponge (a foam block wrapped in sand­paper) until it feels smooth and even. Prime, and then paint.
A garbage disposal is a bit scary when it’s turned on and the blades are noisily chopping up kitchen waste. But, if your disposal gets stinky, fear not. It’s easy to clean out the gunk and get rid of the smell. If the splash guard needs replacing, you can do that in 20 minutes! If you need to replace the entire disposal you can replace it yourself.
Our Repair Programs focus on a variety of tasks that keep the homeowner safe in their own home.   When possible, volunteer labor is offered at no cost to homeowners. Materials and services are paid for by the homeowner through a not-for-profit loan agreement. The scope of work is defined by SCHFH and agreed on by both parties before the work begins. 
Quick-setting drywall compound lets you finish small repairs and fill deep holes in minutes instead of waiting days for premixed joint compound to dry. The small boxes are available in most home centers and paint stores are also easier to store and more likely to get used up than large bags or buckets. Click here to learn how to hang drywall like a pro. Click here to buy drywall compound on Amazon now.
How to DIY it: You should already be emptying the lint trap before every load of laundry. To do a thorough cleaning of the dryer and its vent duct system, unplug the machine (and turn off the gas valve if it has one). Pry off the access panel on the front (try a putty knife covered with duct tape to prevent scratching) and vacuum around the motor and heating element (above). Then carefully disconnect the vent duct tubing from the back of the dryer and use a dryer vent brush (about $10 at home 
centers; look for one that also cleans refrigerator coils) to pull out any 
accumulated lint. Aim to do this at least once a year.
It is instinctual for homeowners to contact an HVAC tech when they notice irregularities in their cooling or heating system. These irregularities could be a direct result of a dirty or clogged air filter. We encourage homeowners to check their filters and replace if necessary. It’s also beneficial for homeowners with pets, carpet, or for homes near fields or construction zones to have multiple filters for convenient replacement.
A 2018 HomeAdvisor survey found that homeowners underestimated the cost of fixing or updating just about everything in their homes. When it came to interior painting, for example, survey participants estimated the work would cost $734. But the national average is $1,744. One of the few items they overestimated was a new toilet — the average is $370, not $405.
×