How to DIY it: Clean up any rough edges around the hole, then stick the patch onto the wall over the hole (left). Using the taping knife, spread a layer of joint compound over it and let it dry overnight. Then spread a wider second coat, feathering out the compound on all sides to make the patch blend in. Let it dry, then apply one more coat extending 8 to 12 inches beyond the patch in all directions. After the final coat dries, sand the area with a sanding sponge (a foam block wrapped in sandpaper) until it feels smooth and even. Prime, and then paint.
How to DIY it: Take off the loose bar by removing the screws on each of the posts that mount the bar to the wall. (If one side is solidly attached, leave it alone.) With the mounting plate now exposed, try tightening the screws in it. If that doesn’t work, remove it. Chances are you’ll find two plastic anchors underneath. Poke them with a screwdriver and let them fall inside the wall. Replace with bigger, stronger metal toggle anchors (above), sold at hardware stores. Just drive them into the existing holes with a drill or a screwdriver, and then reattach everything.
How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.
Depending on where you live, national averages can seem like a steal. Rene Artale’s four-bedroom house near Newcastle, in Westchester County, N.Y., suffered some damage during a storm last winter. A tree fell in the yard, damaging her fence, arbor and retaining wall. And heavy snow caused her roof to leak. The repair bills just kept piling up. Removing the tree, $3,800. Repairing the wall, $4,000. Fixing the roof, $3,800. Fixing the picket fence, $2,800. “It’s obscene,” Ms. Artale, 47, said.
Intimidated by this seemingly daunting project? Don’t be. If you have the will and a whole day (or two) to yourself, you can refinish the hardwood floors in the major areas of your home. You don’t necessarily need to sand, but if the floor is damaged enough to warrant buffing, check out your local hardware store and rent the equipment for anywhere from 4-48 hours. Here’s how to refinish your hardwood floors.
In 2009, there were national handyman service firms which handle such nationwide tasks as public relations, marketing, advertising, and signage, but sell specific territories to franchise owners. A franchise contract typically gives a franchise owner the exclusive right to take service calls within a given geographical area. The websites of these firms put possible customers in touch with local owners, which have handymen and trucks. Customers call the local numbers. Typically these firms charge around $100/hour, although fees vary by locality and time of year. In many parts of the world, there are professional handyman firms that do small home or commercial projects which claim possible advantages such as having workers who are insured and licensed. Their branch offices schedule service appointments for full-time and part-time handymen to visit and make repairs, and sometimes coordinate with sub-contractors.
Check for cracked housings on plastic roof vents and broken seams on metal ones. You might be tempted to throw caulk at the problem, but that solution won’t last long. There’s really no fix other than replacing the damaged vents. Also look for pulled or missing nails at the base’s bottom edge. Replace them with rubber-washered screws. In most cases, you can remove nails under the shingles on both sides of the vent to pull it free. There will be nails across the top of the vent too. Usually you can also work those loose without removing shingles. Screw the bottom in place with rubber-washered screws. Squeeze out a bead of caulk beneath the shingles on both sides of the vent to hold the shingles down and to add a water barrier. That’s much easier than renailing the shingles.
For most people, the home is the biggest investment. Naturally, you want to protect that investment. Rather than waiting for what would have been a small inexpensive repair to grow into a much larger, more costly expense, you need to take preventive maintenance steps. If it has been a while since your home has been assessed, now is the time to have it checked out. Learn how Home Assessments can boost your Kansas City area home’s value.
The average single-family homeowner spends around $2,000 a year on maintenance, according to Bankrate.com. That is considerably less than the monthly fees for most condos or co-ops. But even though the monthly outlay for those homeowners might be lower than that of condo or co-op owners, house owners generally are not squirreling away those savings for a rainy day. Nearly half of them have less than $1,000 saved, and a third have nothing saved, according to Liberty Mutual Insurance. So when that sump pump suddenly fails, odds are, we’re scrambling to pay the plumber for a new one.
Generally the job of paid handyman is low status, a semi-skilled labor job. It's a less prestigious occupation than a specialist such as a plumber, electrician, or carpenter. With the emergence of large national chains, an effort is being made to change that perception, by emphasizing professionalism and the fact that a handyman is actually a technician with multiple skills and a wide range of knowledge. At the same time, unpaid homeowners skilled at repairs are valued for saving money. And handyman tools sometimes become useful in different places: for example, when a proper neurological drill was not available, an Australian doctor used a handyman's drill in 2009 to open a hole in the head of a 13-year-old boy to relieve pressure after a brain injury; the boy's life was saved.
How to DIY it: This job can be messy, so protect nearby surfaces by covering them with plastic or cardboard. Spray the springs with garage door lubricant (about $7 at home centers). Don’t use oil, grease, or other lubricants. They may be cheaper, or you may have them on hand already, but they won’t work as well and tend to pick up dust and grit—just what you don’t want on moving parts.