There's no national standard or regulation for handymen. Licensing and regulation vary by state. New Jersey, for example, requires handymen who work for a profit to register with the state and carry insurance. California requires handymen to carry a license from the State Contractors License Board to work on any project that exceeds $500 in labor and material costs. Find out before you hire the handyman if he or she has the skills needed to complete your project.
Check for cracked housings on plastic roof vents and broken seams on metal ones. You might be tempted to throw caulk at the problem, but that solution won’t last long. There’s really no fix other than replacing the damaged vents. Also look for pulled or missing nails at the base’s bottom edge. Replace them with rubber-washered screws. In most cases, you can remove nails under the shingles on both sides of the vent to pull it free. There will be nails across the top of the vent too. Usually you can also work those loose without removing shingles. Screw the bottom in place with rubber-washered screws. Squeeze out a bead of caulk beneath the shingles on both sides of the vent to hold the shingles down and to add a water barrier. That’s much easier than renailing the shingles.

How to DIY it: This job can be messy, so protect nearby surfaces by covering them with plastic or cardboard. Spray the springs with garage door lubricant (about 
$7 at home centers). Don’t use oil, grease, or other lubricants. They may be cheaper, or you may have them on hand already, but they won’t work as well and tend to pick up dust and grit—just what you don’t want on moving parts.
Even tasks that seem relatively small can add up. Consider the French doors that David Sievers, 53, and his wife, Ulin Sargeant, 47, installed two years ago to replace sliding glass doors on their two-bedroom house in Monrovia, Calif. The doors cost $2,000. But then they paid $1,700 for installation, $500 for a painter to restore the stucco and paint, and $1,600 for an engineering plan required by the city.
When a home is sold, inspections are performed that may reveal environmental hazards such as radon gas in the basement or water supply or friable asbestos materials (both of which can cause lung cancer), peeling or disturbed lead paint (a risk to children and pregnant women), in-ground heating oil tanks that may contaminate ground water, or mold that can cause problems for those with asthma or allergies. Typically the buyer or mortgage lender will require these conditions to be repaired before allowing the purchase to close. An entire industry of environmental remediation contractors has developed to help home owners resolve these types of problems.

You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
Most newer cabinets have self-closing hinges that hold the doors shut. Others have magnetic or roller catches. A catch that no longer keeps a door closed is either broken or out of adjustment. Catches are fastened with two screws, so replacing a damaged catch is simple. Adjustment is just as simple, but you might have to readjust the catch a couple of times before you get it right. Loosen the screws, move the catch in or out, and tighten the screws. If the door doesn’t close tightly, try again.
So last year, Mr. Hark and Mr. Larivee, who works in digital marketing, sold their condo and moved to a four-bedroom house, also in West Orange. They now have to mow their lawn and shovel their driveway when it snows, but when they had a drainage problem in the backyard, they got to choose their contractor and schedule the job based on when it made the most financial sense for them.
If you don’t cover paint chips with touch up paint, they’ll rust and then you’ll have a much bigger problem on your hands. The actual touch up is easy. Just buy touch up paint, fine tip paint applicators and wax and grease remover from any auto parts store. Clean the chip with the wax and grease remover and let it dry. Then dip the applicator in the paint and dab it onto the chip. Don’t add too much or the paint will drip. Let it dry completely and apply wax after 30 days. Get the full guide to using auto touch-up paint here.
How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.

José was quick to respond to my request for an estimate to install a new back door. He came over and sized it up, sent me a fair priced quote the next day, and was back with workers soon after I accepted the quote and immediately started working. I'm extremely satisfied with the work that was performed--and the door needed to be framed and set inside the metal frames for the house, which is a little more complex than a regular door installation. I will definitely hire Jose and Jireh Contractor again!
×