If you find that drawer slides are bent, rollers are broken or rollers won’t turn even after lubricating, replacement is the best solution. To keep the project simple, buy new slides that are identical (or almost identical) to the old ones. That way, replacement is an easy matter of unscrewing the old and screwing on the new. Remove a drawer track and a cabinet track and take them shopping with you. Learn how to build an under-cabinet drawer here.
Any property repair services are only as good as the people and the tools behind them. That’s why we use only the latest repair and maintenance equipment on every job, no matter how small. Part of our job is to ensure your house is up-to-date and looking its best, so we use only the best resources available in order to make that happen. We offer a variety of handyman services throughout the DC area, including all of the following:
When you book a handyman through the Handy platform, they'll arrive with a wealth of experience and expertise. From home repair tasks to odd jobs and general labor, a professional handyman will have the know-how and the can-do to get your place looking brand new. In addition to bringing their experience, a Handy handyman will bring all the tools required to get the job done. All you need to do is tell us your address and a few details about the job into the booking request form, and we’ll connect you with an experienced handyman who’s done plenty of jobs like yours.
How to DIY it: You should already be emptying the lint trap before every load of laundry. To do a thorough cleaning of the dryer and its vent duct system, unplug the machine (and turn off the gas valve if it has one). Pry off the access panel on the front (try a putty knife covered with duct tape to prevent scratching) and vacuum around the motor and heating element (above). Then carefully disconnect the vent duct tubing from the back of the dryer and use a dryer vent brush (about $10 at home 
centers; look for one that also cleans refrigerator coils) to pull out any 
accumulated lint. Aim to do this at least once a year.
If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
Comment: I need to have two smoke detectors installed, One is in the master bedroom (vaulted ceiling) and one in the basement. I need 4 lights installed in the kitchen (vaulted ceiling). I need the battery replaced in the smoke detector in the living room (vaulted ceiling). Lastly, I would like the light bulbs replaced in 4 ceiling fans. They are in the florida room, living room (vaulted ceiling), master bedroom (vaulted ceiling), and second bedroom.
Plumbing vent boots can be all plastic, plastic and metal, or even two-piece metal units. Check plastic bases for cracks and metal bases for broken seams. Then examine the rubber boot surrounding the pipe. That can be rotted away or torn, allowing water to work its way into the house along the pipe. With any of these problems, you should buy a new vent boot to replace the old one. But if the nails at the base are missing or pulled free and the boot is in good shape, replace them with the rubber-washered screws used for metal roofing systems. You’ll find them at any home center with the rest of the screws. You’ll have to work neighboring shingles free on both sides. If you don’t have extra shingles, be careful when you remove shingles so they can be reused. Use a flat bar to separate the sealant between the layers. Then you’ll be able to drive the flat bar under the nail heads to pop out the nails.
My name is Troy I'm a carpenter by trade with the exception of my first year out of high school I spent as a taping Apprentice and three semesters I worked painting when I was in college, its all I've ever done. I also do furniture assembly some Plumbing and Electrical (installing gfi's,ceiling fans, switching out plugs and switches)& a little HVAC.
How to DIY it: Gently tug the loose part of the carpet to find the point where it’s still attached. Snip 
it off as close to the backing as possible and save it. Use painter’s tape to surround the repair area. Squeeze 
a heavy bead of carpet seam sealer (about $6 at home centers) into the run. Then fill in the hole with the saved fiber, using a screwdriver to press it into the sealer bit by bit until the area looks like the surrounding 
carpet (below).
The term handyman increasingly describes a paid worker, but it also includes non-paid homeowners or do-it-yourselfers. Tasks range from minor to major, from unskilled to highly skilled, and include painting, drywall repair, remodeling, minor plumbing work, minor electrical work, household carpentry, sheetrock, crown moulding, and furniture assembly (see more complete list below.) The term handyman is occasionally applied as an adjective to describe politicians or business leaders who make substantial organizational changes, such as overhauling a business structure or administrative division.[6][7]
How to DIY it: This job can be messy, so protect nearby surfaces by covering them with plastic or cardboard. Spray the springs with garage door lubricant (about 
$7 at home centers). Don’t use oil, grease, or other lubricants. They may be cheaper, or you may have them on hand already, but they won’t work as well and tend to pick up dust and grit—just what you don’t want on moving parts.
×