Everyone has a different skill set, and not everyone was put on this planet with the same aptitude for manual labor. And that’s okay! Whatever your needs, the Handy platform can connect you with the right professionals who won’t be daunted by your task, whatever it might be. Whether you need help with a door that won’t close, a squeaky hinge, drywall repair, or fixing a broken table leg, we’ve got you covered.  You can’t go wrong with Handy—let us connect you with a top-rated handyman with the right skills for your job.
When you use the Handy app or website, you’ll be connected with local handyman professionals who can take care of this work for you. In addition to freeing up your time for the more important things in life, booking a handyman through the Handy platform will give you the security of knowing that things are being handled by an expert. If the sight of a hammer or screwdriver fills you with anxiety and you’d rather leave things to a professional, the Handy platform is ready to help.
How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.
Plumbing vent boots can be all plastic, plastic and metal, or even two-piece metal units. Check plastic bases for cracks and metal bases for broken seams. Then examine the rubber boot surrounding the pipe. That can be rotted away or torn, allowing water to work its way into the house along the pipe. With any of these problems, you should buy a new vent boot to replace the old one. But if the nails at the base are missing or pulled free and the boot is in good shape, replace them with the rubber-washered screws used for metal roofing systems. You’ll find them at any home center with the rest of the screws. You’ll have to work neighboring shingles free on both sides. If you don’t have extra shingles, be careful when you remove shingles so they can be reused. Use a flat bar to separate the sealant between the layers. Then you’ll be able to drive the flat bar under the nail heads to pop out the nails.
When you purchase handyman services through the Handy platform, it’s hard to know every detail and requirement up front. That’s why it always helps to have a handyman service professional who is able to react and respond to your job’s needs, whatever they might be. It turns out, when you’ve done as many handyman tasks and home repair jobs as the handyman professionals on the Handy platform, you get pretty adaptable. We’re confident that we’ll be able to connect you with a handyman whose skills suit both your needs and your budget.

If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.
Turn2Us Handyman Services was created with the homeowner in mind. Our goal is to help you with all your household projects by providing a full handyman service or simply providing a handyman to help you with your to-do list. No need to call multiple businesses to handle your projects, we can do it all! We are dedicated to providing you with the best handyman service available at the most affordable price without sacrificing quality.
Our Repair Programs focus on a variety of tasks that keep the homeowner safe in their own home.   When possible, volunteer labor is offered at no cost to homeowners. Materials and services are paid for by the homeowner through a not-for-profit loan agreement. The scope of work is defined by SCHFH and agreed on by both parties before the work begins. 
How to DIY it: Coils are located 
on the back of the refrigerator or across the bottom. Pull the fridge away from the wall. (Hint: Grab the sides and pull from the bottom. You may want to lay cardboard on the floor first to prevent scratching.) Clean coils with a coil-cleaning brush (about $10 at home centers), then vacuum. Do this every six months or so.
Sussex County Habitat for Humanity offers a Home Repair Program that performs repair services to help low-income homeowners impacted by age, disability and family circumstances reclaim their homes with pride and dignity. Volunteer teams work to improve the condition of homes by painting, landscaping, and performing minor repairs at minimal costs to homeowners who would otherwise be unable to complete home repairs on their own.  In addition, SCHFH now offers home repair and renovation services on a larger scale that aim to alleviate critical health, life and safely issues.  Able-bodied homeowners are asked to work alongside the volunteers in a cooperative effort.
×