If you find that drawer slides are bent, rollers are broken or rollers won’t turn even after lubricating, replacement is the best solution. To keep the project simple, buy new slides that are identical (or almost identical) to the old ones. That way, replacement is an easy matter of unscrewing the old and screwing on the new. Remove a drawer track and a cabinet track and take them shopping with you. Learn how to build an under-cabinet drawer here.
Comment: I need to have two smoke detectors installed, One is in the master bedroom (vaulted ceiling) and one in the basement. I need 4 lights installed in the kitchen (vaulted ceiling). I need the battery replaced in the smoke detector in the living room (vaulted ceiling). Lastly, I would like the light bulbs replaced in 4 ceiling fans. They are in the florida room, living room (vaulted ceiling), master bedroom (vaulted ceiling), and second bedroom.
Check for cracked housings on plastic roof vents and broken seams on metal ones. You might be tempted to throw caulk at the problem, but that solution won’t last long. There’s really no fix other than replacing the damaged vents. Also look for pulled or missing nails at the base’s bottom edge. Replace them with rubber-washered screws. In most cases, you can remove nails under the shingles on both sides of the vent to pull it free. There will be nails across the top of the vent too. Usually you can also work those loose without removing shingles. Screw the bottom in place with rubber-washered screws. Squeeze out a bead of caulk beneath the shingles on both sides of the vent to hold the shingles down and to add a water barrier. That’s much easier than renailing the shingles.
When you hire handyman services, you need to be sure that the team is going to turn up on time. Nothing is more frustrating than being given an 8 hour arrival window, forcing you to take a day off of work to sit around and wait. And nothing is more frustrating than a last minute cancellation. When you book handyman services through Handy, you can be sure that they'll arrive at the time you request. We’ll connect you with the right people for the job so you can worry about the things that really need your attention—not fixing that light fixture.
When a home is sold, inspections are performed that may reveal environmental hazards such as radon gas in the basement or water supply or friable asbestos materials (both of which can cause lung cancer), peeling or disturbed lead paint (a risk to children and pregnant women), in-ground heating oil tanks that may contaminate ground water, or mold that can cause problems for those with asthma or allergies. Typically the buyer or mortgage lender will require these conditions to be repaired before allowing the purchase to close. An entire industry of environmental remediation contractors has developed to help home owners resolve these types of problems.
If you don’t cover paint chips with touch up paint, they’ll rust and then you’ll have a much bigger problem on your hands. The actual touch up is easy. Just buy touch up paint, fine tip paint applicators and wax and grease remover from any auto parts store. Clean the chip with the wax and grease remover and let it dry. Then dip the applicator in the paint and dab it onto the chip. Don’t add too much or the paint will drip. Let it dry completely and apply wax after 30 days. Get the full guide to using auto touch-up paint here.
With Grandma’s handymen in Aurora, Parker, Highlands Ranch and Denver, handyman help is just a phone call away! Our Denver handyman staff specializes in home maintenance and repair, and is experienced in a variety of trades including plumbing, painting, drywall, electrical, and carpentry. Click here for a list of our handyman services in Aurora, Denver, Parker, Highlands Ranch, Lone Tree, Centennial, Littleton, Lakewood, and Englewood.
How to DIY it: This job can be messy, so protect nearby surfaces by covering them with plastic or cardboard. Spray the springs with garage door lubricant (about $7 at home centers). Don’t use oil, grease, or other lubricants. They may be cheaper, or you may have them on hand already, but they won’t work as well and tend to pick up dust and grit—just what you don’t want on moving parts.